Lead and Drinking Water - City of Harrodsburg

Facts About Lead and Drinking Water

We are pleased to provide our customers with this important information about lead in drinking water.

Our Approach to Corrosion Control

We take steps to reduce the potential for lead to leach from your pipes into the water. This is accomplished by pH adjustment and monitoring the corrosivity of the water and its potential to leach from your pipes. Currently we do not add corrosion inhibitors to the water leaving our treatment facilities. Some source waters are non-aggressive by nature, meaning there is no need to add corrosion control treatment.

Results from Lead Sampling

The results from samples collected in your water system are included in your annual water quality report (also known as the Consumer Confidence Report), which can be found on our website. Customers are notified via their water bill and will be provided a link to the page or where a hard copy can be obtained.

Because service lines, faucet fixtures, household pipes, and/or solder can contribute significantly to the lead and copper levels in tap water, we ask our customers to collect samples in their homes. These samples are collected on a routine basis (by monitoring once every three years) at homes that are considered vulnerable based on when they were constructed and the materials used. We do this monitoring according to the requirements of the Lead and Copper Rule and use the results to confirm that our corrosion control strategy is operating as intended.

Assessing Your Exposure to Lead

Homes built before 1930 are more likely to have lead plumbing systems. Lead pipes are a dull grey color and scratch easily revealing a shiny surface. Lead solder used to join copper pipes is a silver or grey color. If your house was built before January 1986, you are more likely to have lead-soldered joints.

The best way to know what kind of plumbing and service lines you have in your home is to hire a licensed plumber. Every home is different and it is important that you do not rely on your neighbors for information, as their home could be different.

Lead levels in drinking water are more likely to be higher if:

your home or water system has lead pipes or has a lead service line
your home has copper pipes with lead solder
your home was built before 1986

AND
you have soft or acidic water
water sits in the pipes for long periods of time or has low usage

Minimizing Your Exposure to Lead

You cannot see, smell or taste lead, and boiling water will not remove lead. Although our water is treated to minimize the risk of lead, you can reduce your household’s exposure to lead in drinking water by following these simple steps:

Flush your tap before drinking or cooking with water, if the water in the faucet has gone unused for more than six hours. The longer the water lies dormant in your home’s plumbing, the more potential for it to contain lead. Flush your tap with cold water for 30 seconds to two minutes before using. To conserve water, catch the running water and use it to water your plants.
Try not to cook with or drink water from the hot water faucet. Hot water has the potential to contain more lead than cold water. When you need hot water, heat cold water on the stove or in the microwave.
Remove loose lead solder and debris from plumbing. In newly-constructed homes or homes in which the plumbing was recently replaced, remove the strainers from each faucet and run the water for 3 to 5 minutes. When replacing or working on pipes, be sure to use materials that are lead-free. Use of lead-based solders has been banned.
Look for the “Lead Free” Label. When replacing or installing fixtures, look for the “lead free” label. Under the 2011 Reduction of Lead in Drinking Water Act, fixtures must have 0.25% lead or less to be considered “lead free.”
Routinely clean faucet screens. Sediment and metals can collect in the faucet screen located at the tip of your faucets. Replace screens that are in poor condition. New screens are available at local hardware stores.

To clear the faucet screen of debris:

1. Unscrew the screen.

2. Separate the individual parts.

3. Remove any sediment (mineral or rust build up) on the screen and other parts. If necessary, soak the parts in white vinegar for a few minutes and scrub with a brush.

4. Reassemble the screen parts and reattach to faucet.

The American Water Works Association (AWWA) offers guidance on cleaning aerators. https://www.awwa.org/searchresults.aspx?q=cleaning%20aerators

Home Treatment for Lead

The need for a home treatment device or filter is a customer-specific decision. As described above, we take steps to reduce the potential for lead to leach from your pipes into the water. Please note that certain home treatment devices, such as water softeners for example, might increase lead levels in your water. Always consult the device manufacturer for information on potential impacts to your drinking water or household plumbing.

Before purchasing a home water treatment device, consider local water quality, cost and maintenance, product performance and certifications to make sure the unit will meet your needs. Home treatment devices require regular service. When homeowners do not maintain the unit as recommended by the manufacturer, it reduces the effectiveness and possibly results in lower quality water.

For more information regarding home treatment, customers may choose to visit the NSF website at http://www.nsf.org/Certified/DWTU/.

Getting Your Water Tested for Lead

Lead and/or copper levels in some homes and businesses might be detected due to customer use of lead pipes, lead solder and molded metal faucets in household plumbing. The City of Harrodsburg is will provide testing for lead for individual customers who request it. For customers who would like to be tested for lead, the City of Harrodsburg will collect samples and deliver at the customers cost to a certified laboratory. The cost for Lead testing is $20 each, and for Copper is $20.00 each.

Additional Information

-- USEPA Lead Information
Kentucky Division of Water

EPA’s Safe Drinking Water Act Hotline: 1-800-426-4791